Make LUFA stack as default for ADB converter

converter/adb_usb/Makefile

@@ -1,5 +1,45 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
 # Target file name (without extension).
-TARGET = adb_usb
+TARGET = adb_usb_lufa
 
 # Directory common source filess exist
 TOP_DIR = ../..
@@ -7,7 +47,7 @@ TOP_DIR = ../..
 # Directory keyboard dependent files exist
 TARGET_DIR = .
 
-# keyboard dependent files
+# project specific files
 SRC =	keymap.c \
 	matrix.c \
 	led.c \
@@ -16,22 +56,47 @@ SRC =	keymap.c \
 CONFIG_H = config.h
 
 
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
 
 # Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
 F_CPU = 16000000
 
 
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
 # Boot Section Size in *bytes*
 #   Teensy halfKay   512
 #   Teensy++ halfKay 1024
@@ -44,20 +109,23 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
 # Build Options
 #   comment out to disable the options.
 #
-#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-#MOUSEKEY_ENABLE = yes	# Mouse keys(+5000)
-#EXTRAKEY_ENABLE = yes	# Audio control and System control(+600)
-#CONSOLE_ENABLE = yes    # Console for debug
-#COMMAND_ENABLE = yes    # Commands for debug and configuration
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes	# USB Nkey Rollover(+500)
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
 
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
 
 # Search Path
 VPATH += $(TARGET_DIR)
 VPATH += $(TOP_DIR)
 
-include $(TOP_DIR)/protocol/pjrc.mk
+include $(TOP_DIR)/protocol/lufa.mk
 include $(TOP_DIR)/protocol.mk
 include $(TOP_DIR)/common.mk
 include $(TOP_DIR)/rules.mk

converter/adb_usb/Makefile.lufa

@@ -1,131 +0,0 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-#                Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-#            have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-#             have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-#               (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-#                (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging, 
-#              with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-#                   bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# Target file name (without extension).
-TARGET = adb_usb_lufa
-
-# Directory common source filess exist
-TOP_DIR = ../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# project specific files
-SRC =	keymap.c \
-	matrix.c \
-	led.c \
-	adb.c
-
-CONFIG_H = config.h
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
-
-
-# Optimize size but this may cause error "relocation truncated to fit"
-#EXTRALDFLAGS = -Wl,--relax
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
-
-include $(TOP_DIR)/protocol/lufa.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk

converter/adb_usb/Makefile.pjrc

@@ -0,0 +1,63 @@
+# Target file name (without extension).
+TARGET = adb_usb_pjrc
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC =	keymap.c \
+	matrix.c \
+	led.c \
+	adb.c
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162       # Teensy 1.0
+MCU = atmega32u4       # Teensy 2.0
+#MCU = at90usb646       # Teensy++ 1.0
+#MCU = at90usb1286      # Teensy++ 2.0
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 16000000
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+5000)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+600)
+CONSOLE_ENABLE = yes    # Console for debug
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes	# USB Nkey Rollover(+500)
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol/pjrc.mk
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk