removed my handwired boards to a new branch.

keyboards/handwired/atreus50/Makefile

@@ -1,3 +0,0 @@
-ifndef MAKEFILE_INCLUDED
-	include ../../../Makefile
-endif

keyboards/handwired/atreus50/atreus50.c

@@ -1 +0,0 @@
-#include "atreus50.h"

keyboards/handwired/atreus50/atreus50.h

@@ -1,18 +0,0 @@
-#ifndef ATREUS50_H
-#define ATREUS50_H
-
-#include "quantum.h"
-
-#define KEYMAP( \
-	K000, K001, K002, K003, K004, K005,       K007, K008, K009, K010, K011, K012, \
-	K100, K101, K102, K103, K104, K105,       K107, K108, K109, K110, K111, K112, \
-	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, \
-	K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312  \
-) { \
-	{ K000,  K001,  K002,  K003,  K004,  K005,  KC_NO, K007,  K008,  K009,  K010,  K011,  K012 }, \
-	{ K100,  K101,  K102,  K103,  K104,  K105,  KC_NO, K107,  K108,  K109,  K110,  K111,  K112 }, \
-	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  K212 }, \
-	{ K300,  K301,  K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312 }  \
-}
-
-#endif

keyboards/handwired/atreus50/config.h

@@ -1,58 +0,0 @@
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6060
-#define DEVICE_VER      0x0001
-#define MANUFACTURER    qmkbuilder
-#define PRODUCT         Atreus50
-#define DESCRIPTION     Keyboard
-
-/* key matrix size */
-#define MATRIX_ROWS 4
-#define MATRIX_COLS 13
-
-/* key matrix pins */
-#define MATRIX_ROW_PINS { F4, F5, F6, F7 }
-#define MATRIX_COL_PINS { D3, D2, D1, D0, D4, C6, D7, E6, B4, B5, B6, B2, B3 }
-#define UNUSED_PINS
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
-/* number of backlight levels */
-
-#ifdef BACKLIGHT_PIN
-#define BACKLIGHT_LEVELS 3
-#endif
-
-/* Set 0 if debouncing isn't needed */
-#define DEBOUNCING_DELAY 5
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-/* key combination for command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
-/* prevent stuck modifiers */
-#define PREVENT_STUCK_MODIFIERS
-
-
-#ifdef RGB_DI_PIN
-#define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 0
-#define RGBLIGHT_HUE_STEP 8
-#define RGBLIGHT_SAT_STEP 8
-#define RGBLIGHT_VAL_STEP 8
-#endif
-
-#endif

keyboards/handwired/atreus50/keymaps/default/Makefile

@@ -1,21 +0,0 @@
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
-MIDI_ENABLE = no            # MIDI controls
-AUDIO_ENABLE = no           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-
-ifndef QUANTUM_DIR
-	include ../../../../Makefile
-endif

keyboards/handwired/atreus50/keymaps/default/keymap.c

@@ -1,128 +0,0 @@
-// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
-// this is the style you want to emulate.
-
-#include "atreus50.h"
-#include "action_layer.h"
-#include "eeconfig.h"
-
-extern keymap_config_t keymap_config;
-
-// Each layer gets a name for readability, which is then used in the keymap matrix below.
-// The underscores don't mean anything - you can have a layer called STUFF or any other name.
-// Layer names don't all need to be of the same length, obviously, and you can also skip them
-// entirely and just use numbers.
-#define _DVORAK 0
-#define _QWERTY 1
-#define _COLEMAK 2
-#define _LOWER 3
-#define _RAISE 4
-#define _ADJUST 16
-
-enum planck_keycodes {
-  DVORAK = SAFE_RANGE,
-  QWERTY,
-  COLEMAK,
-  LOWER,
-  RAISE,
-  BACKLIT
-};
-
-// Fillers to make layering more clear
-#define _______ KC_TRNS
-#define XXXXXXX KC_NO
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    [_DVORAK] = { /* dvorak */
-        { KC_TAB,  KC_QUOT, KC_COMM, KC_DOT,  KC_P,    KC_Y,    _______, KC_F,    KC_G,    KC_C,    KC_R,    KC_L,    KC_SLSH },
-        { KC_ESC,  KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    _______, KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    KC_MINS },
-        { KC_LSFT, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_ENT,  KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    KC_RSFT },
-        { KC_LCTL, KC_LALT, KC_LEFT, KC_RGHT, LOWER,   KC_BSPC, KC_LGUI, KC_SPC,  RAISE,   KC_UP,   KC_DOWN, KC_RGUI, KC_RCTL }
-    },
-    
-    [_QWERTY] = { /* qwerty */
-        { KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    _______, KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_DEL  },
-        { KC_ESC,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    _______, KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT },
-        { KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_ENT,  KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT },
-        { KC_LCTL, KC_LALT, KC_LEFT, KC_RGHT, LOWER,   KC_BSPC, KC_LGUI, KC_SPC,  RAISE,   KC_UP,   KC_DOWN, KC_RGUI, KC_RCTL }
-    },
-    
-    [_COLEMAK] = { /* colemak */
-        { KC_TAB,  KC_Q,    KC_W,    KC_F,    KC_P,    KC_G,    _______, KC_J,    KC_L,    KC_U,    KC_Y,    KC_SCLN, KC_DEL  },
-        { KC_ESC,  KC_A,    KC_R,    KC_S,    KC_T,    KC_D,    _______, KC_H,    KC_N,    KC_E,    KC_I,    KC_O,    KC_QUOT },
-        { KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_ENT,  KC_K,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT },
-        { KC_LCTL, KC_LALT, KC_LEFT, KC_RGHT, LOWER,   KC_BSPC, KC_LGUI, KC_SPC,  RAISE,   KC_UP,   KC_DOWN, KC_RGUI, KC_RCTL}
-    },
-    
-    [_LOWER] = {
-        { KC_TILD, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, _______, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, _______ },
-        { KC_CAPS, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   _______, KC_F6,   KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE },
-        { _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  _______, KC_F12,  KC_MUTE, KC_VOLD, KC_VOLU, _______, _______ },
-        { _______, _______, KC_HOME, KC_END,  _______, KC_DEL,  _______, KC_INS,  _______, KC_PGUP, KC_PGDN, _______, _______ }
-    },
-    [_RAISE] = {
-        { KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    _______, KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    _______ },
-        { KC_CAPS, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   _______, KC_F6,   KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_BSLS },
-        { _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  _______, KC_F12,  KC_MPRV, KC_MPLY, KC_MNXT, _______, _______ },
-        { _______, _______, KC_HOME, KC_END,  _______, KC_DEL,  _______, KC_INS,  _______, KC_PGUP, KC_PGDN, _______, _______ }
-    },
-    [_ADJUST] = {
-        { KC_F11,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   _______, KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F12  },
-        { _______, RESET,   _______, _______, _______, _______, _______, _______, QWERTY,  COLEMAK, DVORAK,  _______, _______ },
-        { _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ },
-        { _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ }
-    },
-
-};
-
-const uint16_t PROGMEM fn_actions[] = {
-
-};
-
-void persistant_default_layer_set(uint16_t default_layer) {
-  eeconfig_update_default_layer(default_layer);
-  default_layer_set(default_layer);
-}
-
-bool process_record_user(uint16_t keycode, keyrecord_t *record) {
-  switch (keycode) {
-        case QWERTY:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_QWERTY);
-          }
-          return false;
-          break;
-        case COLEMAK:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_COLEMAK);
-          }
-          return false;
-          break;
-        case DVORAK:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_DVORAK);
-          }
-          return false;
-          break;
-        case LOWER:
-          if (record->event.pressed) {
-            layer_on(_LOWER);
-            update_tri_layer(_LOWER, _RAISE, _ADJUST);
-          } else {
-            layer_off(_LOWER);
-            update_tri_layer(_LOWER, _RAISE, _ADJUST);
-          }
-          return false;
-          break;
-        case RAISE:
-          if (record->event.pressed) {
-            layer_on(_RAISE);
-            update_tri_layer(_LOWER, _RAISE, _ADJUST);
-          } else {
-            layer_off(_RAISE);
-            update_tri_layer(_LOWER, _RAISE, _ADJUST);
-          }
-          return false;
-          break;
-      }
-    return true;
-};

keyboards/handwired/atreus50/rules.mk

@@ -1,56 +0,0 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
-CONSOLE_ENABLE ?= no	# Console for debug(+400)
-COMMAND_ENABLE ?= no    # Commands for debug and configuration
-SLEEP_LED_ENABLE ?= no  # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= no  # Enable keyboard backlight functionality
-AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= no

keyboards/handwired/xk66/Makefile

@@ -1,3 +0,0 @@
-ifndef MAKEFILE_INCLUDED
-	include ../../../Makefile
-endif

keyboards/handwired/xk66/config.h

@@ -1,162 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6060
-#define DEVICE_VER      0x0001
-#define MANUFACTURER    Xyverz
-#define PRODUCT         XK-66
-#define DESCRIPTION     A hand-wired 66-key keyboard by Xyverz
-
-/* key matrix size */
-#define MATRIX_ROWS 5
-#define MATRIX_COLS 14
-
-/*
- * Keyboard Matrix Assignments
- *
- * Change this to how you wired your keyboard
- * COLS: AVR pins used for columns, left to right
- * ROWS: AVR pins used for rows, top to bottom
- * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
- *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
- *
-*/
-#define MATRIX_ROW_PINS { B5, B4, D7, D6, D4 }
-#define MATRIX_COL_PINS { B6, F7, F6, F5, F4, F1, F0, D1, D0, B7, B3, B2, B1, B0 }
-#define UNUSED_PINS
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
- 
-// #define BACKLIGHT_PIN B7
-// #define BACKLIGHT_BREATHING
-// #define BACKLIGHT_LEVELS 3
-
-
-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
-#define DEBOUNCING_DELAY 5
-
-/* define if matrix has ghost (lacks anti-ghosting diodes) */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-/*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
-//#define FORCE_NKRO
-
-/*
- * Magic Key Options
- *
- * Magic keys are hotkey commands that allow control over firmware functions of
- * the keyboard. They are best used in combination with the HID Listen program,
- * found here: https://www.pjrc.com/teensy/hid_listen.html
- *
- * The options below allow the magic key functionality to be changed. This is
- * useful if your keyboard/keypad is missing keys and you want magic key support.
- *
- */
-
-/* key combination for magic key command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
-/* control how magic key switches layers */
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
-
-/* override magic key keymap */
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
-//#define MAGIC_KEY_HELP1          H
-//#define MAGIC_KEY_HELP2          SLASH
-//#define MAGIC_KEY_DEBUG          D
-//#define MAGIC_KEY_DEBUG_MATRIX   X
-//#define MAGIC_KEY_DEBUG_KBD      K
-//#define MAGIC_KEY_DEBUG_MOUSE    M
-//#define MAGIC_KEY_VERSION        V
-//#define MAGIC_KEY_STATUS         S
-//#define MAGIC_KEY_CONSOLE        C
-//#define MAGIC_KEY_LAYER0_ALT1    ESC
-//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
-//#define MAGIC_KEY_LAYER0         0
-//#define MAGIC_KEY_LAYER1         1
-//#define MAGIC_KEY_LAYER2         2
-//#define MAGIC_KEY_LAYER3         3
-//#define MAGIC_KEY_LAYER4         4
-//#define MAGIC_KEY_LAYER5         5
-//#define MAGIC_KEY_LAYER6         6
-//#define MAGIC_KEY_LAYER7         7
-//#define MAGIC_KEY_LAYER8         8
-//#define MAGIC_KEY_LAYER9         9
-//#define MAGIC_KEY_BOOTLOADER     PAUSE
-//#define MAGIC_KEY_LOCK           CAPS
-//#define MAGIC_KEY_EEPROM         E
-//#define MAGIC_KEY_NKRO           N
-//#define MAGIC_KEY_SLEEP_LED      Z
-
-/*
- * Feature disable options
- *  These options are also useful to firmware size reduction.
- */
-
-/* disable debug print */
-//#define NO_DEBUG
-
-/* disable print */
-//#define NO_PRINT
-
-/* disable action features */
-//#define NO_ACTION_LAYER
-//#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
-//#define NO_ACTION_FUNCTION
-
-#endif

keyboards/handwired/xk66/keymaps/default/Makefile

@@ -1,21 +0,0 @@
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
-MIDI_ENABLE = no            # MIDI controls
-AUDIO_ENABLE = no           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-
-ifndef QUANTUM_DIR
-	include ../../../../Makefile
-endif

keyboards/handwired/xk66/keymaps/default/config.h

@@ -1,8 +0,0 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
-
-#include "../../config.h"
-
-// place overrides here
-
-#endif

keyboards/handwired/xk66/keymaps/default/keymap.c

@@ -1,90 +0,0 @@
-#include "xk66.h"
-#include "action_layer.h"
-#include "eeconfig.h"
-
-extern keymap_config_t keymap_config;
-
-// Each layer gets a name for readability, which is then used in the keymap matrix below.
-// The underscores don't mean anything - you can have a layer called STUFF or any other name.
-// Layer names don't all need to be of the same length, obviously, and you can also skip them
-// entirely and just use numbers.
-#define _DV 0
-#define _QW 1
-#define _CM 2
-#define _FL 3
-
-// Macro name shortcuts
-#define QWERTY M(_QW)
-#define DVORAK M(_DV)
-#define COLEMAK M(_CM)
-
-// Fillers to make layering more clear
-#define _______ KC_TRNS
-#define XXXXXXX KC_NO
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-[_DV] = KEYMAP ( /* Dvorak */
-        KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_LBRC, KC_RBRC, KC_BSPC, \
-        KC_TAB,  KC_QUOT, KC_COMM, KC_DOT,  KC_P,    KC_Y,    KC_F,    KC_G,    KC_C,    KC_R,    KC_L,    KC_SLSH, KC_EQL,  KC_BSLS, \
-        MO(_FL), KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    KC_MINS,          KC_ENT,  \
-        KC_LSFT,          KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    KC_RSFT,          \
-        KC_LCTL, KC_LALT, KC_LGUI, KC_LEFT, KC_RGHT, KC_BSPC, KC_SPC,           KC_UP,   KC_DOWN, KC_RGUI, KC_RALT, KC_RCTL, MO(_FL)
-       ),
-
-[_QW] = KEYMAP ( /* Qwerty */
-        KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, \
-        KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS, \
-        MO(_FL), KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT,  \
-        KC_LSFT,          KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,          \
-        KC_LCTL, KC_LALT, KC_LGUI, KC_LEFT, KC_RGHT, KC_BSPC, KC_SPC,           KC_UP,   KC_DOWN, KC_RGUI, KC_RALT, KC_RCTL, MO(_FL)
-       ),
-
-[_CM] = KEYMAP ( /* Colemak */
-        KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, \
-        KC_TAB,  KC_Q,    KC_W,    KC_F,    KC_P,    KC_G,    KC_J,    KC_L,    KC_U,    KC_Y,    KC_SCLN, KC_LBRC, KC_RBRC, KC_BSLS, \
-        MO(_FL), KC_A,    KC_R,    KC_S,    KC_T,    KC_D,    KC_H,    KC_N,    KC_E,    KC_I,    KC_O,    KC_QUOT,          KC_ENT,  \
-        KC_LSFT,          KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,          \
-        KC_LCTL, KC_LALT, KC_LGUI, KC_LEFT, KC_RGHT, KC_BSPC, KC_SPC,           KC_UP,   KC_DOWN, KC_RGUI, KC_RALT, KC_RCTL, MO(_FL)
-       ),
-
-[_FL] = KEYMAP ( /* Function Layer 1 */
-        KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  _______, \
-        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
-        _______, _______, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______, QWERTY,  DVORAK,  COLEMAK, _______, _______,          _______, \
-        KC_CAPS,          _______, KC_MUTE, KC_VOLD, KC_VOLU, _______, _______, _______, _______, _______, _______, _______,          \
-        RESET,   _______, _______, KC_HOME, KC_END,  KC_DEL,  KC_INS,           KC_PGUP, KC_PGDN, _______, _______, _______, _______
-       ),
-
-};
-
-
-const uint16_t PROGMEM fn_actions[] = {
-
-};
-
-void persistant_default_layer_set(uint16_t default_layer) {
-  eeconfig_update_default_layer(default_layer);
-  default_layer_set(default_layer);
-}
-
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
-      switch(id) {
-        case _DV:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_DV);
-          }
-          break;
-        case _QW:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_QW);
-          }
-          break;
-        case _CM:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_CM);
-          }
-          break;
-      }
-    return MACRO_NONE;
-};

keyboards/handwired/xk66/keymaps/default/readme.md

@@ -1 +0,0 @@
-# The default keymap for handwired/xk66

keyboards/handwired/xk66/readme.md

@@ -1,28 +0,0 @@
-handwired/xk66 keyboard firmware
-======================
-
-## Quantum MK Firmware
-
-For the full Quantum feature list, see [the parent readme](/).
-
-## Building
-
-Download or clone the whole firmware and navigate to the keyboards/handwired/xk66 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. 
-
-Depending on which keymap you would like to use, you will have to compile slightly differently.
-
-### Default
-
-To build with the default keymap, simply run `make default`.
-
-### Other Keymaps
-
-Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files.
-
-To build the firmware binary hex file with a keymap just do `make` with a keymap like this:
-
-```
-$ make [default|jack|<name>]
-```
-
-Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.

keyboards/handwired/xk66/rules.mk

@@ -1,67 +0,0 @@
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no            # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE ?= no            # MIDI controls
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no           # Audio output on port C6

keyboards/handwired/xk66/xk66.c

@@ -1,8 +0,0 @@
-#include "xk66.h"
-
-void matrix_init_kb(void) {
-	// put your keyboard start-up code here
-	// runs once when the firmware starts up
-
-	matrix_init_user();
-}

keyboards/handwired/xk66/xk66.h

@@ -1,25 +0,0 @@
-#ifndef XK66_H
-#define XK66_H
-
-#include "quantum.h"
-#include "led.h"
-
-
-// This a shortcut to help you visually see your layout.
-// The first section contains all of the arguements
-// The second converts the arguments into a two-dimensional array
-#define KEYMAP( \
-    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0a, K0b, K0c, K0d, \
-    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1a, K1b, K1c, K1d, \
-    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2a, K2b,      K2d, \
-    K30,      K32, K33, K34, K35, K36, K37, K38, K39, K3a, K3b, K3c,      \
-    K40, K41, K42, K43, K44, K45, K46,      K48, K49, K4a, K4b, K4c, K4d  \
-) { \
-    { K00, K01,   K02, K03, K04, K05, K06, K07,   K08, K09, K0a, K0b, K0c,   K0d   }, \
-    { K10, K11,   K12, K13, K14, K15, K16, K17,   K18, K19, K1a, K1b, K1c,   K1d   }, \
-    { K20, K21,   K22, K23, K24, K25, K26, K27,   K28, K29, K2a, K2b, KC_NO, K2d   }, \
-    { K30, KC_NO, K32, K33, K34, K35, K36, K37,   K38, K39, K3a, K3b, K3c,   KC_NO }, \
-    { K40, K41,   K42, K43, K44, K45, K46, KC_NO, K48, K49, K4a, K4b, K4c,   K4d   } \
-}
-
-#endif